Chemistry 9 RO

Chapter test · TC: Core curriculum (1 hour a week)

Chemistry test, grade 9: chapter 11, Gases – what presses on the walls of a balloon

10 questions · 1 point for each right answer · 20 minutes · Lessons 11.1, 11.2

Back to the teachers’ page

Full nameClassDate
  1. What produces the pressure of a gas enclosed in a balloon?

    1. The weight of the gas, pushing on the bottom of the balloon
    2. Gas particles colliding with the walls
    3. Attraction between gas particles
    4. Heat released by the walls of the balloon
  2. Put the distributor’s steps for when you smell gas in order, from first to last.

    Write the number of the step in the box: 1 for the first, 6 for the last.

    • Do not operate switches or use sockets, electronic devices or sources of flame
    • Call 112
    • Turn off the gas supply
    • Notify the distributor on its emergency number
    • Open the windows
    • Leave the room immediately
  3. One mole of helium and one mole of carbon dioxide are at normal conditions. What volume does each occupy?

    1. Helium occupies less because its atoms are smaller
    2. Carbon dioxide occupies less because it is heavier
    3. Each occupies 11.2 L
    4. Each occupies 22.4 L
  4. Why must you not operate switches when you smell gas?

    1. A spark can ignite the mixture of methane and air
    2. Electric current reacts with mercaptans
    3. The light uses up the oxygen in the room
    4. The switch stops ventilation through the windows
  5. The pressure of a gas is 1.5 atm. What is it in mmHg?

    Answer: mmHg

  6. What amount of gas, in moles, is in 4.1 L at 3 atm and 27 °C? Use R = 0.082 L·atm/(mol·K).

    Answer: mol

  7. A rigid container holds gas at 1.5 atm and 27 °C. What is the pressure, in atm, after it is heated to 127 °C?

    Answer: atm

  8. Put the steps for solving a pV = nRT problem in order.

    Write the number of the step in the box: 1 for the first, 5 for the last.

    • Write down the data
    • Write pV = nRT and rearrange for the required quantity
    • Convert temperature to kelvin, pressure to atm and volume to L
    • Calculate and check the unit and order of magnitude
    • Substitute with R = 0.082
  9. A trapped gas is compressed to half its original volume at constant temperature. How does its pressure change?

    1. It halves
    2. It doubles
    3. It stays the same
    4. It quadruples
  10. What temperature goes into the equation pV = nRT for a gas at 27 °C?

    1. 27 K
    2. 246 K
    3. 300 K
    4. 27 °C

Key: chapter 11, TC

Page for the teacher. Each question is worth 1 point if the whole answer is right; for the ordering and grouping questions the point is given only for the complete answer. The teacher decides the grade scale.

  1. b) Gas particles colliding with the walls. Collisions exert a continuous force on the wall; force divided by area is pressure. (lesson 11.1)

  2. The correct order: 1. Do not operate switches or use sockets, electronic devices or sources of flame; 2. Open the windows; 3. Turn off the gas supply; 4. Leave the room immediately; 5. Notify the distributor on its emergency number; 6. Call 112. First avoid any spark, then ventilate and turn off the gas, then leave; call the emergency numbers from outside the building, as the distributor says. (lesson 11.1)

  3. d) Each occupies 22.4 L. The particles are far apart, so the volume is practically independent of the type of gas: 1 mol occupies 22.4 L at normal conditions. (lesson 11.1)

  4. a) A spark can ignite the mixture of methane and air. Methane mixed with air explodes in the presence of a spark, and a switch can produce one. (lesson 11.1)

  5. 1,140 mmHg (a difference of up to 0.5 is accepted). 1 atm = 760 mmHg, so 1.5 · 760 = 1,140 mmHg. (lesson 11.1)

  6. 0.50 mol (a difference of up to 0.005 is accepted). n = pV ÷ (RT) = 3 · 4.1 ÷ (0.082 · 300) = 12.3 ÷ 24.6 = 0.5 mol. (lesson 11.2)

  7. 2.0 atm (a difference of up to 0.01 is accepted). Volume is constant, so p₂ = p₁ · T₂ ÷ T₁ = 1.5 · 400 ÷ 300 = 2 atm. (lesson 11.2)

  8. The correct order: 1. Write down the data; 2. Convert temperature to kelvin, pressure to atm and volume to L; 3. Write pV = nRT and rearrange for the required quantity; 4. Substitute with R = 0.082; 5. Calculate and check the unit and order of magnitude. Convert the units to match those of R before substituting, then check the result at the end. (lesson 11.2)

  9. b) It doubles. At constant T, p · V is constant: if V halves, p doubles. (lesson 11.2)

  10. c) 300 K. T(K) = t(°C) + 273, so 27 + 273 = 300 K. (lesson 11.2)